GentooForum.de

Quellcode

# /etc/init.d/wlan0 start                                                                                                                                                                                                                                            
 * Bringing up interface wlan0
 *   ERROR: interface wlan0 does not exist
 *   Ensure that you have loaded the correct kernel module for your hardware
 * ERROR: wlan0 failed to start

Quellcode

eth0, lo und vboxnet0

Quellcode

* Bringing up interface wlan0
 *   Configuring wireless network for wlan0
 *   Scanning for access points
 *      does not support scanning
 *   You either need to set a preferred_aps list in /etc/conf.d/wireless
 *      preferred_aps="SSID1 SSID2"
 *      and set associate_order_wlan0="forcepreferred"
 *      or set associate_order_wlan0="forcepreferredonly"
 *   or hardcode the  SSID to "any" and let the driver find an Access Point
 *      ssid_wlan0="any"
 *   or configure defaulting to Ad-Hoc when Managed fails
 *      adhoc_ssid_wlan0="WLAN"
 *   or hardcode the SSID against the interface (not recommended)
 *      ssid_wlan0="SSID"
 *   Failed to configure wireless for wlan0
 * ERROR: wlan0 failed to start

Quellcode

modules="wpa_supplicant" 
wpa_supplicant_wlan0="-Dwext" 
config_wlan0="dhcp"

Quellcode

# You can also override the interface settings found in /etc/conf.d/net 
# per SSID - which is very handy if you use different networks a lot 
#config_SSID="dhcp" 
#dhcpcd_SSID="-t 5" 
#routes_SSID= 
#fallback_SSID=

Quellcode

config_FritzBox="192.168.0.53/24 brd 192.168.0.255"
routes_FritzBox="default via 192.168.0.1"
dns_servers_FritzBox="192.168.0.1"

Quellcode

cat /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib64/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.

# PCI device 0x14bv:0x8164 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="d7:4a:a9:22:af:4a", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

# PCI device 0x8186:0x4132 (iwlagn)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="3e:00:14:94:31:14", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"

Quellcode

02:00.0 Network controller: Intel Corporation Device 4239 (rev 35)
        Subsystem: Intel Corporation Device 1311
        Flags: bus master, fast devsel, latency 0, IRQ 38
        Memory at da100000 (64-bit, non-prefetchable) [size=8K]
        Capabilities: [c8] Power Management version 3
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
        Capabilities: [e0] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [140] Device Serial Number 00-22-14-fe-ff-96-32-17
        Kernel driver in use: iwlagn
        Kernel modules: iwlagn

Quellcode

net-wireless/iwl6000-ucode
     Available versions:  (~)9.221.4.1
     Installed versions:  9.221.4.1(23:12:58 15.09.2010)
     Homepage:            http://intellinuxwireless.org/?p=iwlwifi
     Description:         Intel (R) Wireless WiFi Advanced N 6000 ucode

Quellcode

lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11abgn  Mode:Managed  Frequency:2.442 GHz  
          Access Point: Not-Associated   Tx-Power=15 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          
vboxnet0  no wireless extensions.