ne sorry das war nur ein schreib fehler von mir
mount -t ntfs >/dev/sda1 /mnt/usbhdd
bash: /dev/sda1: No such device or address
eine eingebaute hdd ist weitaus leichter für mich einzubinden aber mit usb-hdd hmm die mögen mich ned
naja auf der usb-hdd sind mp3 oben und im moment ist es sehr still hier zu still
brauch music .....
naja was kann ich noch machen ?? wie ich die hdd ein binden und mounten kann ??
________________________________________________________________________________
hier mal die komplette ausgabe von dmesg
vieleicht hilft das weiter ?
Linux version 2.6.12-gentoo-r6 (root@livecd) (gcc version 3.3.5-20050130 (Gentoo 3.3.5.20050130-r1, ssp-3.3.5.20050130-1, pie-8.7.7.1)) #1 Sat Nov 19 21:25:16 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Gentoo ro root=343
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2004.436 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904932k/917504k available (2706k kernel code, 12116k reserved, 1009k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3964.92 BogoMIPS (lpj=1982464)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router default [10de/01e0] at 0000:00:00.0
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1133860435.492:0): initialized
inotify device minor=63
Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
NTFS driver 2.1.22 [Flags: R/O].
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
nvidiafb: nVidia device/chipset 10DE0253
nvidiafb: nVidia Corporation NV25 [GeForce4 Ti 4200]
nvidiafb: CRTC0 not found
nvidiafb: CRTC1 found
nvidiafb: EDID found from BUS2
nvidiafb: CRTC 0appears to have a CRT attached
nvidiafb: Using CRT on CRTC 0
nvidiafb: MTRR set to ON
Console: switching to colour frame buffer device 80x30
nvidiafb: PCI nVidia NV25 framebuffer (64MB @ 0xD8000000)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35.
PCI: Setting latency timer of device 0000:00:04.0 to 64
input: AT Translated Set 2 keyboard on isa0060/serio0
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda
MA, hdb
MA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc
MA, hdd
MA
Probing IDE interface ide0...
hda: WDC WD800JB-00FMA0, ATA DISK drive
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
hdb: MAXTOR 4K080H4, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
hdd: ASUS DVD-ROM E616, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/2000KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 >
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 4, io mem 0xea000000
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 5, io mem 0xea003000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 11, io mem 0xea004000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v2.2
usb 1-3: new high speed USB device using ehci_hcd and address 4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
PCI: Setting latency timer of device 0000:00:06.0 to 64
usb 2-1: new low speed USB device using ohci_hcd and address 2
input: USB HID v1.10 Joystick [Logitech WingMan Precision USB] on usb-0000:00:02.0-1
intel8x0_measure_ac97_clock: measured 49683 usecs
intel8x0: clocking to 47380
ALSA device list:
#0: C-Media PCI CMI8738-MC6 (model 55) at 0xd000, irq 7
#1: NVidia nForce2 with ALC650F at 0xea002000, irq 3
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.
http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k freed
kjournald starting. Commit interval 5 seconds
usb 2-2: new low speed USB device using ohci_hcd and address 3
input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:02.0-2
input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:02.0-2
usb 3-2: new low speed USB device using ohci_hcd and address 2
input: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:02.1-2
Adding 1953496k swap on /dev/hdb2. Priority:-1 extents:1
EXT3 FS on hdb3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS volume version 3.1.
NTFS volume version 3.1.